Bases come with firing arcs and without. They are compatible with the entire Omni-Stand line of flight stands.
Price:
Without Arcs - $1.24 each
With Arcs - $1.74 each
Volume discounts available.
]]>
We have decided to change our policy and start shipping using First Class mail for international orders. This allows us to ship most of our orders for a lot less.
When CorSec started out most of our orders tended to be larger. In recent months, We have seen a decrease in our average order totals. This is mainly due to the Omni-Rulers and repeat Omni-Stand customers. We hope that this new shipping policy will allow our international customers to have easier access to our products.
Shipping charges are now based on the total amount of the order.
$0.01 - $20.00 orders will be charged $5.00
$20.01 - $60.01 orders will be charged $8.00
$60.01 - $115.00 orders will be charge $10.00
Orders over $115.00 orders will be charge $16.95 and sent priority mail if possible.
The Fabric Mats will be shipped only through Priority Mail. This really only affects the 72" by 42" versions because they fall below the $115.00 cutoff.
]]>
Bases come with firing arcs and without. They are compatible with the entire Omni-Stand line of flight stands.
Price:
Without Arcs - $1.24 each
With Arcs - $1.74 each
Volume discounts available.
]]>
All of our current patterns are now available in this size.
Cost: $119.99
]]>Both styles are back in stock.
]]>Price: $0.45 each (volume discounts available)
Omni-Stand Small Magnetic Mounts
Price: $0.99 each (volume discounts available)
The Small Mounts are roughly 1/4" in diameter and just under 3/16" high. This is a much better profile then the original mounts that measured 3/8" in height. They work with all the Omni-Stand rods and other accessories.
We took some shots of a Micro Armor 1/285th scale HS 129B with the mounts. This is a very small plane and it looks great with the small mount attached.
We have also used this as a base to create a smaller magnetic mount. The rare earth magnet is 1/4" in diameter. This is a great deal smaller then the original mount that measured 3/8" in diameter. Both sizes of mounts will work with these magnets.
The magnets are very strong and should hold up most miniatures without a problem.
Future releases will include a gatehouse and corner towers. We are also going to release a 28mm version.
Price:
With rods $1.99 per section
Without rods $1.49 per section
1" Sections are $0.49 each
1" End Caps are $0.74 each
We decided to paint up a few sections and show them off. The miniatures are Earth Force Marines and a Merka 5 Tank by Rebel Minis.
The fence is a really light weight. It can stand on its own. but we added a small washer to the bottom to give it a bit more stability. A fender washer could also be used. This will give a bit of room for foliage at the uprights.
A better angle on the fence.
The sections are around 50mm high. This is a good 3 times as big as the figures. It should work great for 15mm. It also looks good for Battletech or Heavy Gear.
]]>
We have completed the first prototype Clear Omni-Stand Rod. The rod consists of 1/4" diameter clear rod with steel threads at either end. This should still provide good strength and have the added benefit of being clear. They will be cheaper then the metal rods and only a 1/16" increase in the diameter.We are working on reducing the thread insert depth to give it a cleaner look. We hope to be ready for full production really soon.
Each fence section consists of two uprights and a base.Each upright support has 8 x 1/6" diameter holes drilled into it. Brass, Styrene, or wooden dowels make great barriers. You can even use florescent acrylic rods for a more futuristic look. The top has a very small hole that can be used for threading barbed wire from support to support.
Each section clips into the one next to it. They can be permanently attached or used independently to give you more flexibility when building your compound.
The entire set is designed to work with 15mm figures. The supports are 48mm high.
The corner pieces will come with small guard towers.
The tower is designed to hold a single figure on a penny base.
The acrylic can be painted to give it any look you need for your favorite setting. Adding a small washer or penny to the base pieces will give it more stability and help keep those nasty dinosaurs out.
Once the 15mm set has been completed, we plan to upscale it to 28mm.
We hope to have these available next month or the early part of January.
]]>